![arduino usb host shield pin 9 arduino usb host shield pin 9](https://static.wixstatic.com/media/6b1fb2_f98587eb60dd4439892d67abf2074b07~mv2.jpg)
- #ARDUINO USB HOST SHIELD PIN 9 HOW TO#
- #ARDUINO USB HOST SHIELD PIN 9 SERIAL#
- #ARDUINO USB HOST SHIELD PIN 9 ANDROID#
![arduino usb host shield pin 9 arduino usb host shield pin 9](https://www.mikrocontroller.net/attachment/347178/shield.gif)
Applying voltages higher than 3.3V to any I/O pin could damage the board. The maximum voltage that the I/O pins can tolerate is 3.3V. Warning: Unlike most Arduino boards, the Arduino Due board runs at 3.3V.
#ARDUINO USB HOST SHIELD PIN 9 SERIAL#
It has 54 digital input/output pins (of which 12 can be used as PWM outputs), 12 analog inputs, 4 UARTs (hardware serial ports), a 84 MHz clock, an USB OTG capable connection, 2 DAC (digital to analog), 2 TWI, a power jack, an SPI header, a JTAG header, a reset button and an erase button. It is the first Arduino board based on a 32-bit ARM core microcontroller. Both connect to the same TWI interface to allow you to create a chain of TWI devices.The Arduino Due is a microcontroller board based on the Atmel SAM3X8E ARM Cortex-M3 CPU. The on-board connectors are :Ģ TinkerKit Inputs: IN2 and IN3(in white), these connectors are routed to the Arduino A2 and A3 analog input pins.Ģ TinkerKit Outputs: OUT5 and OUT6 (in orange), these connectors are routed to the Arduino PWM outputs on pins 5 and 6.Ģ TinkerKit TWI: these connectors (4-pin in white) are routed on the Arduino TWI interface. Connecting TinkerKit modules can simplify the creation of a project or a prototype.
![arduino usb host shield pin 9 arduino usb host shield pin 9](https://www.pjrc.com/teensy/td_libs_USBHostShield_1.jpg)
The shield features several TinkerKit input/output and communication interfaces. This shield has a MALE USB port where you can attach your USB device. The Arduino USB Host Shield has no power jack and is powered only when attached to an Arduino board Max Current: 500mA when Arduino is powered by a suitable power supply connected to the Arduino power jackĤ00mA when Arduino is powered by its USB port Pins 7, 8 and 9 are used for GPX, INT and RES pins. On both boards, pin 10 is used to select the MAX3421E. This is on digital pins 10, 11, 12, and 13 on the Uno and pins 10, 50, 51, and 52 on the Mega. For more information, see the Arduino communicates with the MAX3421E using the SPI bus (through the ICSP header).
#ARDUINO USB HOST SHIELD PIN 9 HOW TO#
If you are building an accessory that uses USB, make sure you understand how to implement the AOA protocol to establish communication between your accessory hardware and Android.
#ARDUINO USB HOST SHIELD PIN 9 ANDROID#
can be audio docking stations, exercise machines, personal medical testing devices, weather stations, or any other external hardware device that adds to the functionality of Android.Accessories use the Android Open Accessory (AOA) protocol to communicate with Android devices, over a USB cable or through a Bluetooth connection. Note that the distance between digital pins 7 and 8 is 160 mil (0.16"), not an even multiple of the 100 mil spacing of the other pins. Four screw holes allow the board to be attached to a surface orcase.
![arduino usb host shield pin 9 arduino usb host shield pin 9](https://cdn.sparkfun.com/assets/parts/3/4/7/0/09628-01.jpg)
The maximum length and width of the Motor Shield PCB are 2.7 and 2.1 inches respectively. Mass storage devices: USB sticks, memory card readers, external hard drives, etc. ADK-capable Android phones and tables.ĭigital cameras: Canon EOS, Powershot, Nikon DSLRs and P&S, as well as generic PTP. USB to serial converters: FTDI, PL-2303, ACM, as well as certain cell phones and GPS receivers. Game controllers: Sony PS3, Nintendo Wii, Xbox360. HID devices: keyboards, mice, joysticks, etc. The shield is TinkerKit compatible, which means you can quickly create projects by plugging TinkerKit modules onto the board. The Arduino USB Host Shield is based on the MAX3421E which is a USB peripheral/host controller containing the digital logic and analog circuitry necessary to implement a full-speed USB peripheral or a full-/low-speed host compliant to USB specification rev 2.0. The Arduino USB Host Shield allows you to connect a USB device to your Arduino board.